Magic balloon introduction The magic balloon, also known as the long balloon in China, is also a kind of rubber balloon. This balloon can be shaped into a variety of interesting shapes, such as various animals, flowers, weapons, etc. It brings a lot of fun to children and even adults. Magicians and clowns sometimes perform on stage. >>Optional: Magic Balloon |  |
â– Magic balloon hot product recommendation
| Special offer 1.5g birthday party balloons wholesale 100 magic balloon arch wedding supplies balloons thickening | Joint venture strip balloon thickening magic balloon shape balloon strip balloon clown balloon 100 Pack | Thicken 260 Magic Balloon Variety Shape Balloon Balloon Wholesale 100 Pack Long Strip Balloon Wholesale | Long balloon decoration balloon * magic balloon * wedding supplies * modeling balloon 0.15 yuan / month |
| Magic props close-up idea burst balloon street horror Magicsmith-Bloon exclusive new product | Magic strip balloon magic balloon strip balloon shape balloon balloon 100 only sells 8.8 yuan | Apple balloon magic balloon package apple grass 500 bunch balloon special tools 55 yuan | Wedding wedding wedding room layout supplies magic balloon wholesale mixed color thick pearl light balloon 100 |
â– Magic balloon pumping method
Magic balloon pumping method
The magic balloon usually needs a pump to blow it up. Methods as below: 1. Extend the balloon a few times before pumping to reduce its elasticity. 2. Quickly inflate the balloon to the required length, generally 2/3 of the length of the long balloon. 3, before knotting, vent a small part of the gas in the long balloon, reduce the air pressure, make the balloon a little softer, in order to shape. Whether it is made of one or more cylindrical colored balls or complicated or simple, large or small shape or decoration, it is necessary to master its aeration, sealing, single bubble knot, double bubble knot, triple bubble knot, ear bubble Knot some basic craftsmanship and techniques. (1). Inflatable inflatables use a small manual pump. Under normal circumstances, any shape needs to leave a section of uninflated ball at the end of the ball. Before making the styling, it is necessary to roughly determine the amount of inflation required for the styling. If the inflation is too much or too little, even if only a little charge or less charge is applied, the composition effect and production efficiency of the styling will be affected. (2). The sealing of the sealing ball often uses a common backhand knot. Action: (Because the end of the ball after inflation is very short and the ball is tight, the ligation is more difficult.) When inflating, the finger of the pinch ball can be removed from the ball or some gas can be inflated to release the ball. Partially increased. In addition, after the ball is released a little gas, the ball slightly softens and avoids the tension and the explosion of the ball after the twisting. (3). The single bubble knot system twists the cylindrical colored balls into a plurality of individual bulbs of different sizes according to the design ratio, which is the basic unit of various shapes of the colored balls magic. Action: Hold the ball with the left hand and pinch the cylindrical ball into the size or length of the bubble. Rotate the ball in the opposite direction to twist the ball. In most cases, shape any ball on the ball (including double bubble, three bubble) The knotting action of the knot, ring bubble knot, etc. does not exceed three or two turns at most. If it is necessary to continuously make a plurality of blister shapes and prevent the disengagement of the twisted bulbs, the ring finger or the little finger of the golfer can be used to hold the bulb at the beginning of the color ball, and the thumb and the index finger are used to match the other hand. Continue to twist. In addition, if the twisting rotation between the parts is in the same direction, it is more convenient to make the quick and convenient adjustment and disassembly. (4). In the fabrication of the double bubble knot, the three connected rear two circular or strip bulbs are looped in a loop. Action: While bending the two bulbs with both hands, place the left thumb and forefinger of the ball on the bottom of the bubble of the two bulbs and gather them, then rotate the two bulbs in the right hand to screw. It is commonly used in the production of limbs or flowers of animals. (5). In the process of making three bubble knots, three strips of the same length and connected strips are stacked together, one of the bulbs is passed through the other two bulbs and turned into one. Action: Gather three strips of bulbs in both hands, and use the left and right palms and the thumb to separate the strips of the two sides. At the same time, use the forefinger and middle finger of both hands to push and pass the middle strip of bulbs. It is often used in the production of animal bodies or three-color chain decorations. (6). In the production of the earbubble, the middle one of the three connected bulbs is self-wrapped. Action: While bending the three bulbs into a ring with both hands, place the left thumb and forefinger of the ball at the bottom of the bubble of the two bulbs and gather them. Use the right thumb and the two fingers to make the middle bulb slightly. After pulling up, perform self-tightening. It is commonly used in the production of animal's feet, ears and flower petals. (7). The ring bubble knots the cylindrical colored balls in a ring shape. Action: After bending and gathering the inflated colored balls, hold the ball with one hand, hold the bubble joint with one hand, and twist it by twisting it. It is commonly used in the production of animal heads, limbs and leaves of flowers. (8). The broken bubble blasts a bubble in the middle of the three connected circular bulbs to break the bulb in the shape from the bulb. Action: First, make the "ear-bubble knot" one by one on each of the three connected circular bulbs. Each bubbly should be twisted no less than four or five times, and then use a pair of scissors or sharps to make a bubble in the middle. Blasting. If the five connected circular bulbs are disconnected, firstly, the two bulbs on both sides are labeled "double bubble knot", and then one bulb in the middle is blasted. It is commonly used in the separation of animal hands and feet or flower branches and leaves. (9). The buds will shape the strips of the ball end of the ball (about 7CM). Action: Hold the ball with the left hand and use the right index finger to push the ball joint (with the index finger) into the bulb. When the left thumb and forefinger pinch the ball joint between the thumb and the index finger, move the ball with the right thumb and middle finger. The right index finger is withdrawn from the bulb, and the strip bulb is rotated 5-6 times. Then, with the left hand, the ball joint with the ball wound is pushed a small amount to push the strip bulb held by the right hand and fixed.
Men Running shoes are very suitable for all kind of sports like running, walking, mountaineering and paly football and so on. With the top priority good quality and remorseless serivce, we are receiving more and more active feedback from our customers.Looking for ideal of Shoes Manufacturer & supplier ? We have a wide selection at goods prices to help you get creative. All the Shoes are quality guaranteed. We are China Origin Factory of Men Shoes. If you have any question, please feel free to contact us.
Running Shoes,Mesh Running Shoes,Breathable Running Shoes,Men Running Shoes
Ningbo Qizhan Trade Co.,Ltd , https://www.qizhanshoes.com